Update (28/03/2024): We have plenty of stock of all our products, find us also in and    Shop now

simpleRTK2B performance with NTRIP correction services

simpleRTK2B NTRIP precission and accuracy

Prepare yourself a strong coffee because the data shown here will have to be read twice.

In the last post we showed how to connect the simpleRTK2B shield to a NTRIP correction service.
Now we will talk about the performance we got by using this configuration.

A few notes about the tests we performed:

  • We used the functional prototype of the simpleRTK2B shield.
    It looks different than the final product, but the GNSS performance is exactly the same.
  • We used our freshly received active antenna from u-blox.
    We are running in parallel a comparison between u-blox antenna, Tallysman antenna and Ardusimple antenna and we will publish it soon.
    The performance of this antenna is very similar to ours.
  • The performance figures are obtained by using the ERGNSS network from the Instituto Geográfico Nacional, in particular the mountpoint CERCANA3.
    The performance you observe will depend on the type of NTRIP corrections. The one we used is very standard.

We performed two different tests to evaluate the performance:

  1. Static test in a triangulation station (or survey marker)
    Download the complete log here
  2. Dynamic test in a highway with tunnels, bridges, truck overtakes, …
    Download the complete log here

The data shown in this post is not post-processed and you should be able to get the same results by analyzing the logs.

1) Static test with NTRIP corrections

We went to a well known triangulation station to compare the results obtained by the simpleRTK2B with those obtained by high end GNSS stations.
The data we will use is the one inside the green rectangles (latitude, longitude and ellipsoidal height + pillar height).
ICGC triangulation station

This picture shows the test configuration, with the simpleRTK2B and the antenna placed at the top of the pillar.

We logged data from a cold startup during 432 seconds and these are the outputs:
simpleRTK2B NTRIP accuracy

Fix after cold start after 13s, steady state 3D accuracy ~0.54m after 100s from start.
NTRIP connection at t=124.7s and RTK fix in less than 6s.
Estimated 3D accuracy with NTRIP corrections of 17.29mm during the whole time.

These numbers look very good, but since u-blox doesn’t provide a lot of information about how the accuracy is estimated, we compared the data from the simpleRTK2B with the data provided by the triangulation station (for scaling reasons we only show data from the RTK fix period (t∈[130,432]s):
simpleRTK2B NTRIP precission and accuracy
The black crosses are the position and ellipsoidal height defined in the geodetic data.
The black dotted line represent the 95% confidence interval of these measurements.
The green crosses and lines show the position and ellipsoidal height provided by the simpleRTK2B.

Assuming that the real position is the one reported by the geodetic database:

  • simpleRTK2B 2D position accuracy is ~1cm and the altitude accuracy is ~2.5cm
  • simpleRTK2B 2D precision (95% confidence) is ~5mm and the altitude precision (95% confidence) is ~1.5cm

2) Dynamic test with NTRIP corrections

For this test we placed the GNSS antenna at the top of a van and we drove ~25km in a highway.
GNSS antenna

Since we don’t have a true reference to compare our results it is difficult to quantify the performance.
We can use the ZED-F9P 2D accuracy estimation value as a reasonable variable to evaluate the performance.
simpleRTK2B NTRIP dynamic performance

In the above figure we plotted the path of the van in different colors based on the 2D accuracy.
At the end of the path (it starts from the bottom), we couldn’t get a RTK fix and the simpleRTK2B stayed in RTK float with an accuracy around 5cm, probably due to the distance from the NTRIP station, which was located more than 25km away.

As you can see, the ZED-F9P module in the simpleRTK2B shield maintains a good fix at speeds ~120km/h (safety first :)).

The intermittent decreases in 2D accuracy are caused by bridges crossing the highway and some truck overtakings.
We exported the path into Google Earth and by counting the number of blue sections in the figure path, you will get the number of bridges crossing the highway!

The red arrow indicate the bridge location (click image to enlarge).
simpleRTK2B dynamic performance NTRIP

Affordable high precision is really here!

If you liked this content, you can follow us on Twitter, YouTube, Facebook or LinkedIn to stay updated of content like this.

Want to learn more about GPS/RTK?

1. Our engineering team will contact you to solve any questions
2. We will keep you updated about promotions and new product releases
3.You will only hear from us when we have important news, we won’t spam your email