Firmware Upgrade/update Fails simpleRTK2Blite

Q&A forumCategory: QuestionsFirmware Upgrade/update Fails simpleRTK2Blite
cjmssmd asked 10 months ago

I am attempting to update firmware on simpleRTK2Blite.  I have the blue xbee header attached and am attached to my computer via USB. U-Center talks to the device fine, I am getting GPS readings, etc.  When I run the firmware update I get the following logfile.  What am I doing wrong?  Thank you! 
 
Setup pipes
Firmware update tool launched
-p STDIO -b 115200:9600:230400 –no-fis 1 -s 0 -t 0 -v 1 “C:\Users\Chris Milner\Downloads\UBX_F9_100_HPG_112_ZED_F9P.a26bfd58dfd11c233f8fdba6b99adc5a.bin”
———-CMD line arguments———–
Image file: C:\Users\Chris Milner\Downloads\UBX_F9_100_HPG_112_ZED_F9P.a26bfd58dfd11c233f8fdba6b99adc5a.bin
Flash: <compiled-in>
Fis: flash.xml
Port: STDIO
Baudrates: 115200/9600/230400
Safeboot: 0
Reset: 1
AutoBaud: 0
Verbose: 1
Erase all: 1
Erase only: 0
Training sequence: 0
Chip erase: 0
Merging FIS: 1
Update RAM: 0
Use USB alt: 0
—————————————
0.0 u-blox Firmware Update Tool version 19.03
0.0 Updating Firmware ‘C:\Users\Chris Milner\Downloads\UBX_F9_100_HPG_112_ZED_F9P.a26bfd58dfd11c233f8fdba6b99adc5a.bin’ of receiver over ‘STDIO’
0.0 – Opening and buffering image file
0.0 – Verifying image
0.0 – image 0 size 654812
0.0 – image 1 size 411440
0.0 – config size 0
0.0 – Trying to open port STDIO
0.0 – Setting baudrate to 115200
0.3 – Received Version information
0.3 – Receiver currently running SW ‘EXT CORE 1.00 (94e56e)’
0.3 – Receiver HW ‘00190000’, Generation 9.0
0.3 – Sending ROM CRC Poll
0.3 ROM CRC: 0x118B2060
0.3 u-blox9 ROM1.02 hardware detected (0x118B2060)
0.3 Getting Port connection to receiver
0.3 – Connected port is: UART1
0.3 Starting LDR TSK
0.4 – LDR TSK started successfully
0.4 Identify flash loader
0.5 – Uploader version 5.1 detected
0.5 Stop GPS operation
0.5 Detecting Flash manufacturer and device IDs
0.5 – Flash ManId: 0x00EF DevId: 0x4015
0.5 – Not merging anything
0.5 – Flash size: 2097152
0.5 – Flash block: 512 x 4096
0.8 – Setting baudrate to 230400
1.0 Receiver info collected, downloading to flash…
Erasing sector 1/512
Erasing sector 2/512
13.0 WARNING: Sending erase retry for sector 0
13.0 WARNING: Sending erase retry for sector 1
Erasing sector 1/512
Erasing sector 2/512
25.0 WARNING: Sending erase retry for sector 0
25.0 WARNING: Sending erase retry for sector 1
Erasing sector 1/512
Erasing sector 2/512
37.0 WARNING: Sending erase retry for sector 0
37.0 WARNING: Sending erase retry for sector 1
Erasing sector 1/512
Erasing sector 2/512
49.0 WARNING: Sending erase retry for sector 0
49.0 WARNING: Sending erase retry for sector 1
Erasing sector 1/512
Erasing sector 2/512
61.0 ERROR: Erase retries for sector 0 exceeded.
61.0 Firmware Update FAILED

Firmware Update Utility has unexpectedly terminated
Exit code (2)
 
 

cjmssmd replied 10 months ago

(In case it helps, the same firmware update worked just fine on my simpleRTK2B board. Same .bin file, same procedure, etc. – worked fine).

1 Answers
cjmssmd answered 10 months ago

I got it to work by changing the baud rate to 115,200 on the firmware upgrade screen

Ardusimple Staff replied 10 months ago

Great news and thanks for the update!